* Module cascade type (from the front): We explained at the first step, when watch from the front, the signal transfer sequence is from right to left.Īfter you’ve filled all those tech parameters, press “Next”. If you want to learn this, please contact us.) (Actually there’s simple way to know the scan type.
* Scan type: It’s OK to choose “unknown” if you don’t know it. As mentioned above, in this sample, each led module is 32pixels X 32 pixels. * Actual pixel: That’s the led module resolution. Here you need to input the basic tech parameters of the led screen. Key in password “admin”, and you would enter the “screen config” interface.Īfter User Login, we can start to configure the control card. Note: The default IP address of sending card is “192.168.0.208” which is defined in the factory, usually we don’t change it. Now search the control card again, and this time you could find it.Ĭlick “connect terminal”, the laptop will be connected with the sending card. Here I change the IP address of my laptop as below:Īnd also change the relevant place in the software:
XXX” – the IP of the laptop must be in the same net segment with the IP of the sending card, so that the communication between them (computer and control card) could happen. So you’d need to check the IP of the Laptop, and change it to be “192.168.0. Probably you would not find the sending card. Open the software NovaLCT-Pluto, connect the sending card to the laptop with net cable. Configure the Novastar Asynchronous Control Card: The resolution of this led screen is 192 pixels X 96 pixels.ģ. The size of each led module is 320mm X 320mm, with resolution of 32pixels X 32 pixels.Ĥ). Each cabinet consists of 9 modules 3(W)*3(H).ģ). When I face it, the signal transfer sequence is from right to left.Ģ). This P10 smd led screen consists of 2 cabinets. Collect Basic Tech Parameters of the LED Display Hardware:įor instance, here we have two led cabinets with P10 smd led modules, then we install asynchronous Novastar control cards, one sending card, two receive cards on them.Īnd I connect the sending card to the laptop with net cable, and the basic tech parameters of this led display are:ġ). Here we will explain how to configure this file:ġ. In this case, you’d need to set the parameters in the program, and configure the new file. rcfg” file if Novastar) and couldn’t get it from the original supplier. Just like any led display control system, sometimes after long time of operation, the control card may lose the configuration file (“. Due to the high price of these systems, it is usually only recommended for companies that have large fleets of advertising screens spread over very wide geographical areas.Novastar control cards are more and more popular for that they can provide higher refresh rate and processing depth (grey level) especially in the application of small pixel pitch led display screens. This allows you to have full control over the adequate operations of the LED screen. The more advanced and expensive models on the market allow you to carry out exhaustive analysis of the electronic performance of the LED screen. Sometimes, instead of using the temperature sensors, it is necessary to collect the environmental data that is offered from specialized web pages and these are captured and displayed on the LED screen itself. It is important for the temperature sensor to be installed in an area where auxiliary temperatures do not interfere (shaded areas, near heat sources, etc.). This option is configured from the LED screen’s software and you can customize at what time you want to display the environmental temperature captured by the sensor. The temperature sensors measure the room temperature and send it to the card so that it can be displayed on the LED screen itself. That is, these brightness sensors allow us to optimize the brightness of the screen considering the room’s lighting conditions. For example, we can program the screen to reduce its brightness during nighttime so as not to annoy a passerby. These sensors are connected to the sending card, allowing to control the brightness of the LED screen according to the room lighting conditions. It’s the easiest digital signage software you will ever use To get a sense of the main features, check out the overview below. When you purchase an LED sign from Stewart Signs, you receive our exclusive cloud-based digital signage content management system,. In addition to the resolution capability they can offer, they can also perform other auxiliary functions: The Easiest LED Sign Software Youll Ever Use. It is necessary to adapt the resolution of our LED screen to the capacity of each Sending Card. We can have cards that can obtain maximum output resolutions of 1024 x 768 and higher ones with capacities of up to 4K. Sending cards are usually classified according to the resolution capacity they are capable of processing. TECHNICAL SPECIFICATIONS OF A SENDING CARD (Emitter card for LED screens).